Item Description:
DC motor is a rotating motor that can change DC electric power into mechanical strength (DC motor) or mechanical power into DC electric strength (DC generator). It is a motor that can transform DC and mechanical vitality into one particular one more. When it runs as a motor, it is a direct existing motor, which converts electrical energy into mechanical power when it operates as a generator, it is a direct existing generator, which converts mechanical energy into electrical energy.
| Product Name | Z630-4/810KW/550V/310rpm CZPTized DC Motor |
| Motor Type | DC Motor,ACMotor,Stepper Motor,Asynchronous Motor ,Synchronous Motor (CZPT equipment) |
| Composition composition | The framework of DC motor ought to consist of two areas: stator and rotor. The static portion of DC motor is known as stator. The primary perform of stator is to produce magnetic field, which is composed of foundation, main magnetic pole, commutation pole, finish cap, bearing and brush device. Working element is called rotor, whose major perform is to make electromagnetic torque and inductive electromotive force. It is the hub of energy conversion of DC motor. So it is also generally named armature, which is composed of rotor, armature core, armature winding, commutator and supporter. |
| Design | Z Sort |
| Seat number | Z315-Z1000 |
| electrical power | 60~2800kW |
| Voltage | 220~1000V |
| Torque variety | one.five ~180kNm |
| Safety level | IP23, IP44 |
| Cooling mode | IC06,IC17,IC37,IC81W |
| Working velocity | Constant Pace /Reduced Speed /Alter Speed /High Speed Other |
| Main classification | DC Motor is a device that converts mechanical power into DC electrical power. It is largely used as DC motor for DC motor, electrolysis, electroplating, smelting, charging and excitation electrical power offer of alternator. Even though in places in which DC electrical power is needed, AC electrical power rectifier is also employed to change AC into DC energy, but from some factors of overall performance, AC rectifier electrical power offer can not fully change DC generator. |
| Application | DC motors are broadly utilised in tape recorders, video recorders, video discs, electrical shavers, hair dryers, electronic watches, toys and so on. |
| Routine maintenance strategy | Specialist motor upkeep center motor upkeep procedure: cleansing stator and rotor – changing carbon brush or other components – vacuum F stress dipping paint – drying – Calibration stability. 1. Use environment should be always dry, motor floor must be retained cleanse, air ingestion should not be hindered by dust, fibers and other road blocks. two. When the thermal protection of the motor proceeds to run, it should be ascertained whether or not the fault arrives from the motor or the overload or the setting value of the protective gadget is too low. Right after eliminating the fault, it can be place into operation. three, ensure that the motor is properly lubricated in the course of procedure. The general motor operates for about 5000 hrs, that is to say, lubricating grease should be additional or changed. When bearing overheating or lubricating deterioration is found in operation, the hydraulic force should alter lubricating grease in time. When replacing grease, the outdated grease ought to be taken out, and the oil groove of bearing and bearing protect should be washed with gasoline. Then ZL-3 lithium grease should be loaded with one/2 (two poles) and 2/3 (4 poles, 6 poles and eight poles) of the cavity among the inner and outer rings of the bearing. 4. When the daily life of the bearing is above, the vibration and sounds of the motor will enhance obviously. When the radial clearance of the bearing reaches the following price, the bearing need to be changed. 5, when eliminating the motor, it is Okay to remove the rotor from the shaft extension or the non extension end. If it is not necessary to unload the supporter, it is far more convenient to take out the rotor from the non-axle extension stop. When pulling out the rotor from the stator, the stator winding or insulation ought to be prevented from becoming broken. six. When changing the windings, the sort, dimensions, turns and gauges of the first windings need to be recorded. When these knowledge are misplaced, they should be obtained from the manufacturer and the unique designed windings ought to be modified at will, which often deteriorates a single or many performance of the motor or even helps make it impossible to use them. |
